From a tape-measured rectangle to every area unit you need
A rectangular plot is the one case where area is still just length times width. The confusion starts after that, when one person speaks in square feet, another in square yards, a banker in acres and a municipal file in square metres. This page takes one pair of measurements and writes all of those units at once, using the same conversion constants every time: 1 metre = 3.28084 feet, 1 square metre = 10.7639 square feet, 1 square yard = 9 square feet, 1 acre = 43,560 square feet, 1 hectare = 10,000 square metres. A gaj on this page is treated as 9 square feet — the common North-Indian identity — not as a local variant that changes by district.
Worked example: 40 ft × 30 ft
40 × 30 = 1,200 square feet. That is 1,200 × 0.092903 = 111.48 square metres, or 1,200 ÷ 9 = 133.33 square yards (gaj), or 1,200 ÷ 43,560 = 0.0275 acres, or 0.01115 hectares. Those are the defaults the card is built to show. A 12 m × 18 m plot entered in metres is 216 m² (2,325 sq ft, 0.0534 acres). Measure twice if the fence line is not a true rectangle: a tape along a crooked compound wall overstates or understates the saleable area, and no converter will save you from that.
| Sides | Sq ft | Sq m | Sq yd / gaj |
|---|---|---|---|
| 40 × 30 ft | 1,200 | 111.48 | 133.33 |
| 12 × 18 m | 2,325 | 216.00 | 258.33 |
Hindi mein
40×30 फुट का प्लॉट = 1,200 वर्ग फुट = 111.48 वर्ग मीटर = 133.33 गज (9 वर्ग फुट वाला गज)। बीघा-गुंठा जैसी देसी इकाइयाँ इस पेज पर नहीं हैं; उनके लिए लैंड कन्वर्टर खोलें।
Irregular plots
If the site is an L-shape, split it into two rectangles and add the square feet. If it is a trapezium, use (parallel sides added, halved, times height) and then type the resulting area into the sister area converter. A phone’s GPS plot app is a reconnaissance tool, not a substitute for a licensed survey when money changes hands.
How to use this page
- Enter the measurements you actually took, in one unit system at a time.
- Read every converted figure on the card; they all come from the same raw number.
- If a figure will be used on a sale deed, cross-check it against the land-record unit that document uses.
For village units such as bigha, guntha and gaj-by-state, use the existing land converter instead of this page. This tool stays with rectangular plot geometry and SI / imperial area units so the two pages do not impersonate each other.
Conversion constants: 1 ft = 0.3048 m (international foot), 1 acre = 43,560 sq ft, 1 hectare = 10,000 m², 1 sq yd = 9 sq ft. Gaj is shown as 9 sq ft. Local deed units that differ belong on the land-converter page.
A note on precision
The card prints several decimal places so you can see that the conversions are consistent, not because a house plot is known to the nearest square centimetre. A tape stretched on a hot afternoon expands a little; a wall that is “30 ft” on a brochure may be 29 ft 8 in on the ground. Use two decimals for square metres when you are talking to a designer, and stop pretending that 0.027547 acres is more honest than “about three hundredths of an acre”. What matters is that every unit on the card describes the same physical rectangle.
If length and width were measured along a slope, the saleable plan area is the horizontal projection, which is slightly smaller. Surveyors correct for that. A garden calculator does not. For anything that will be registered, pay for the survey rather than leaning on a webpage.