Slab Steel CalculatorA free tool on thebackyardscientist.com

Steel calculator for a slab – kg per m² and TMT D²/162

1,000 sq ft slab par kitna steel? Default 90 kg/m² plus 5% wastage se tonnes nikalte hain. Doosri tab par TMT chhad ka weight D²/162 se. Yeh thumb rule hai, bar-bending schedule nahi.

हिंदी में

Steel for a slab, plus TMT kg/m

Residential slabs in India are often discussed in the 80–105 kg/m² band (about 0.8–1.05 tonnes per 1,000 sq ft) before detailing. This is a thumb rule, not a bar-bending schedule.

How much steel for a 1,000 sq ft slab?

Type “how much steel required for 1000 sq ft slab” into Google and you will land on TMT brand blogs quoting 0.8 to 1.05 tonnes. They are repeating a site thumb rule: residential slab reinforcement often lands around 80 to 105 kilograms per square metre of slab area once you count both ways of the mesh, extras at openings, and a little crank. This page turns that band into an interactive estimate and then, on a second tab, lets you weigh individual TMT bars with the familiar D²/162 formula so you can check a delivery chalan.

Thumb-rule tab

1,000 square feet is 92.903 square metres. At the default 90 kg/m² you get 92.903 × 90 = 8,361 kg before wastage. Add the default 5% for cutting and lap (some estimators use 7–8% on a messy site) and the shopping figure becomes 8,779 kg, about 8.78 tonnes. Move the kg/m² slider down to 80 and the same slab is 7.81 tonnes with wastage; move it up to 105 and you are at 10.24 tonnes. That spread is why a blog that prints a single “8 tonnes per 1,000 sq ft” number without stating kg/m² is not giving you enough to argue with a contractor.

1,000 sq ft slabkg/m²With 5% wastage
Light residential band807,807 kg (7.81 t)
Default on this page908,779 kg (8.78 t)
Heavier residential / more extra bars10510,242 kg (10.24 t)

TMT tab: why D²/162?

The mass of a round steel bar per metre is the cross-section area times the density of steel. Area in mm² is π/4 × D². Density is about 7,850 kg/m³. Working through the units gives kg/m ≈ D² × 0.006165, and 1 ÷ 0.006165 is almost exactly 162. So kg per metre ≈ D² / 162, with D in millimetres. A 12 mm bar weighs 144/162 = 0.889 kg per metre. A 12 metre length is 10.67 kg. Ten such bars are 106.7 kg. The same formula is printed on pretty much every TMT chart in an Indian yard; this tab just saves you the calculator app.

Hindi mein

1,000 वर्ग फुट स्लैब, 90 किलो प्रति वर्ग मीटर, 5% wastage: लगभग 8.78 टन स्टील। यह अंगूठे का नियम है, बार-बेंडिंग शेड्यूल नहीं। 12 मिमी की छड़ का वजन D²/162 से 0.889 किलो प्रति मीटर बैठता है — 12 मीटर की एक छड़ लगभग 10.67 किलो।

What this page will not do

It will not space bars at 150 mm centres or design a cantilever. Those decisions live in a structural drawing. Using a thumb rule to buy steel before the drawing exists is how people either dump extra bars in a corridor or run short before the last panel. Use the estimate to sense-check a quotation, then buy from the schedule. Combine it with the concrete-mix and shuttering tools when you are costing the whole slab, not just the steel line.

How to use

  1. Enter the slab area (1,000 sq ft is the default because that is the question people type).
  2. Pick a kg/m² inside the 80–105 band unless your engineer gave you a different planning figure.
  3. Add 5% wastage, or more if the slab is cut up with many openings.
  4. Switch to the TMT tab to weigh a bundle: diameter, length, count.

D²/162 follows from a 7,850 kg/m³ density and a circular section (IS steel bar charts use the same rounded constant). The 80–105 kg/m² residential slab band is a widely quoted Indian site range, not a clause of IS 456. Always prefer the structural drawing.

When a quotation arrives as “8 tonnes for the slab”, ask which kg/m² they assumed and whether wastage is already inside the number. Two contractors can both be honest and still differ by a tonne on a 1,000 sq ft house if one planned 80 kg/m² and the other 95. This page exists so that conversation has a shared whiteboard.

Frequently asked questions

1000 sq ft slab mein kitna steel?

At 90 kg/m² plus 5% wastage, about 8.78 tonnes. At 80 kg/m² about 7.81 tonnes; at 105 kg/m² about 10.24 tonnes.

D²/162 kya hai?

Kilograms per metre of a round TMT bar, D in millimetres. 12 mm = 0.889 kg/m.

Kya yeh IS 456 design hai?

Nahi. IS 456 and your structural drawing override every number on the thumb-rule tab.

Wastage kitna?

5% is a common cutting and lap extra. Very cut-up slabs may need more.

12 mm × 12 m ek bar?

10.67 kg. Ten bars: 106.7 kg.

Brand blogs 8 tonne kyun likhte hain?

They are rounding the same 80–90 kg/m² band. This page shows the band instead of hiding it.

Thumb rule and unit weight only. Not a structural design or a substitute for an engineer’s bar-bending schedule.